Table of Contents
- About This Guide
- Objectives
- Audience
- Documentation Conventions
- Related Juniper Networks Documentation
- Obtaining Documentation
- Comments About the Documentation
- Requesting Support
- Configuring SNMP Traps
- Overview
- References
- Configuration Tasks
- Creating a Trap Destination
- Related Dialog Box
- Viewing Trap Statistics
- Configuring Policy Management
- Overview
- Terminology
- References
- Configuring Classifier Control Lists
- Creating a Classifier Control List
- Creating a Classifier Control List Entry
- Related Dialog Boxes
- Configuring Traffic Classes
- Configuring Rate-Limit Profiles
- Configuring a One-Rate Rate-Limit Profile
- Configuring a Two-Rate Rate-Limit Profile
- Creating a Policy List
- Adding Rules to a Policy List
- Understanding Policy List Limits
- Creating a Rule
- Removing a Rule
- Modifying Policy Lists
- Associating a Policy List with an IP Interface
- Associating a Policy List with a Profile
- Configuring Virtual Routers
- Overview
- Default Virtual Router
- References
- Configuration Tasks
- Creating Management Access
- Creating Management Access Entries
- Creating Access List Entries
- Creating IP Static Routes
- Configuring VLANs
- Overview
- Configuration Tasks
- Creating VLANs
- Configuring a VLAN
- Associating VLANs with Ethernet Interfaces
- Creating VLAN Interfaces
- Creating Interfaces on VLAN Subinterfaces
- Configuring BGP Neighbors
- Overview
- Configuration Tasks
- Understanding BGP Neighbor Windows
- Creating BGP Neighbors
- Setting Route Policies
- Setting BGP Parameters
- Setting Timers
- Creating Access Lists
- Creating BGP Templates
- Applying a BGP Template
- Configuring IP
- Overview
- Before You Configure IP Interfaces
- Creating IP Interfaces
- Creating an IP Interface with a Numbered or an Unnumbered IP Address
- Creating an IP Loopback Address
- Creating IP Addresses
- Associating Customer Information with an IP Interface
- Configuring Profiles
- Overview
- Profiles with PPP Interfaces
- Profiles with ATM Subinterfaces
- Devices with Different Versions
- Profile Color Codes
- Configuration Tasks
- Creating a Profile
- Task 1: Create and Name the Profile
- Task 2: Choose Profile Settings
- Task 3: Assign IP Settings
- Task 4: Assign PPP Settings
- Task 5: Assign PPPoE Settings
- Associating Profiles
- Associating a Profile with a PPP Interface
- Associating a Profile with an ATM 1483 Subinterface
- Configuring Remote Access
- Overview
- B-RAS Protocol Support
- B-RAS Data Flow
- RADIUS
- DHCP
- References
- Before You Begin
- Configuration Tasks
- Configuring a B-RAS License
- Creating User Domain Maps
- Creating Authentication and Accounting Servers
- Creating DHCP Relay Servers
- Creating Local IP Address Pools
- Configuring and Viewing IP Address Pools
- Configuring IP Tunnel Interfaces
- Overview
- References
- Creating IP Tunnel Interfaces
- Related Dialog Boxes
- Saving Parameter Settings
- Configuring Tunnel Connections
- Overview
- IP Tunnels
- SMDS Tunnels
- HSSI
- GRE Tunnels
- Line Modules
- References
- Creating IP Tunnel Connections
- Creating IP Tunnel Endpoints
- Selecting Available IP Tunnel Interfaces
- Related Dialog Boxes
- Creating SMDS Tunnel Connections
- Creating SMDS Tunnel Endpoints
- Selecting Available GRE Tunnel Interfaces
- Create SMDS Tunnel Connection-Related Dialog Boxes
- Analyzing Tunnel Operation
- Resolving Tunnel Connection Conflicts
- Configuring Config Sync Services
- Overview
- Configuring Config Sync Services
- Getting Status Information
- Locating the Config Sync Services Log
- Uninstalling Config Sync Services
- Uninstalling in Windows
- Uninstalling in Solaris
- Removing Config Sync Services from the NMC-RX Database
- Using the Provisioning Service
- Overview
- Starting the NMC-RX Provisioning Service
- Starting the Provisioning Service
- Sample PVS Scripts
- Testing the NMC-RX Provisioning Service
- Running the PVS Test Utility
- Understanding PVS Test Utility Output
- Using the Provisioning Service
- IDL Interfaces
- Standard IDLs
- Proprietary IDLs
- Configuring Bulk Services
- Overview
- References
- Creating Core Components
- Creating IP over ATM Service
- Creating an ATM Interface
- Creating VP Tunnels
- Creating ATM Subinterfaces
- Creating ATM Circuits
- Creating NBMA Interfaces
- Selecting a Service Type
- Creating ATM Service Type
- Creating Bridged 1483/ATM Service Type
- Creating PPP/ATM Service Type
- Creating PPPoE/ATM Service Type
- Related Dialog Box
- Using Device Utilities
- Overview
- Using Remote Login
- Using Ping
- Using Basic Ping Settings
- Using Advanced Ping Settings
- Using Traceroute
- Using Basic Traceroute Settings
- Using Advanced Traceroute Settings
- Using the Configuration Save and Restore Utilities
- Saving a Configuration File
- Restoring a Configuration File
- Deleting a Configuration File
- Configuring NMC-RX Services Using the Resource Configurator
- Overview
- Running the Resource Configurator
- Configuring the NMC-RX Database
- Running the Database
- Configuring SNMP
- Configuring the Polling Service
- Configuring the Settings in the NMC-RX Resource Configurator Dialog Box
- Configuring the Settings in the Polling Service Tab
- Viewing a User Profile
- Getting Status Information
- Locating the Polling Service Log
- Provisioning Server IDLs
- unspRXDeviceMgr.idl
- unspRXCustomerMgr.idl
- Sample Client Program
- Index